How Frequently Should You Wash Your Dyson V8 Animal Filter
In this guide, you'll learn how to clean your Dyson V8 thoroughly.
This article is split into unlike sections representing the various components of the V8 that require cleaning.
I've purchased several Dyson vacuums over the past year and ran them through various cleaning tests, so the next footstep is to make clean them, which I'll share here.
Tools y'all'll demand
- Safety gloves: First-class way to go on finger marks off the vacuum. I'm kind of OC with smudges. It also will proceed your hands clean.
- Trash container: Get something with a broad opening for disposing of the contents of the dustbin.
- Screwdriver set: You'll need this for disassembling the Dyson V8 cyclone. Get something with a magnetic head as some of the bolts are in deep locations. And then it won't be difficult to reattach the fasteners.
How to clean Dyson V8 filter?
I'll commencement by showing you how to clean the filter.
The V8 comes with 2:
- Pre-motor filter that sits in the center of the cyclones
- Post-motor backside the motor.
Both of these filters are washable. I've read in some blogs to use soapy water, but I'd propose against information technology because it'll permeate through the filter material, thus reducing its effectiveness at filtering fine dirt.
Besides, using soap will make it harder to rinse since you have to remove any soapy residue.
Tap water will suffice.
Steps to clean the pre-motor filter:
- Pull out the pre-motor filter.
- Rinse under running water. Avoid using a scrubby as it may damage the filter textile.
- Wring out excess h2o.
- Please wait for information technology to dry thoroughly before reattaching on the vacuum.
Dyson recommends cleaning the filter in one case a month. For frequent users, it's best to do a visual bank check periodically to cheque for accumulation.
You can remove the superlative function of the filter using a blunt tool. This part is held in identify past clips. Advisedly push the prune using a device (similar in the photograph below).
Don't go too hard, or the plastic holding the clips may snap.
One time the cover out, information technology's easier to clean the inner part of the filter.
To prevent any downtime, buy an extra filter(s), so you'll have something to apply while waiting.
At that place are a ton of options – OEM and replacement. I'd advise spending a flake more than for an original to become the aforementioned filtration without degrading functioning.
We earn a committee if you click this link and make a purchase at no boosted price to you.
Replacement options are less expensive, simply in that location's a risk of it not sifting allergens as well, thus compromising filtration.
How do you clean a Dyson V8 HEPA filter?
- Twist the filter counterclockwise to unlock and remove.
- Rinse under running water to remove whatsoever accumulation of dirt.
- Shake well, and so permit it dry completely before reattaching.
The postal service-motor HEPA filter doesn't need frequent cleaning every bit the pre-motor filter. Dyson cyclones are skilful enough at keeping particles of clay away from information technology.
I checked Dyson, and they didn't mention specifically the interval. Nevertheless, 1 online vacuum store recommends cleaning information technology every iii months.
Please annotation that both filters are what Dyson calls "lifetime," pregnant information technology will last the vacuum'southward lifetime if yous follow the maintenance protocols.
How to make clean Dyson V8 brush head?
The V8 has two types of cleaning heads – the Fluffy attachment and the standard castor.
I'll show you how to clean both. Even if both nozzles tin can resist tangles, it'due south essential to bank check and make clean this part regularly. Any buildup of debris will add extra friction and wear – not good for longevity.
Steps to clean V8 Fluffy tool
1. Remove the plastic clip
Underneath the fluffy attachment, you'll see a plastic commodities property the roller bar in place. Utilize a coin to unlock.
2. Take out the roller attachment
On the right side of the tool, you'll see an arrow graphic. Push this side down to remove the soft roller.
Once this part is out, the smaller roller component backside information technology also comes out.
3. Clean thoroughly
With all the components out, it's easier to make clean the nooks and crannies.
You tin can launder both rollers. Dyson recommends using cold water only. Avoid using detergents equally it can dethrone the material material and only lengthen the process.
Check for whatever mass of pilus on both axles and clean as needed.
iv. Reattach the rollers
If you've washed the rollers, make certain it's fully dry before attaching it on the nozzle.
Identify both rollers back and reattach the cap, and then lock in place.
Steps to make clean the V8 principal cleaning head
1. Remove the cap
Use a coin to remove the cap holding the castor in place.
2. Take out the brush
As you lot twist, the cap will pop out. Remove the lid and brush, then clean.
If hair wraps on the brush, apply a scissor to remove information technology. Don't forget to cheque the axles for any debris aggregating.
Grab a clean microfiber towel and wipe down the components of the nozzle. Also, clean the two pocket-sized wheels in forepart, and the ball system as dust and sand will stick.
3. Reattach the brush
Afterward cleaning, reattach the primary brush and cap. Apply a money to twist and lock in place.
How to clean Dyson V8 cyclone?
Different parts of the V8'southward cyclonic organization.
Lastly, permit'due south look at how to make clean the V8 cyclone. Dyson doesn't have a tutorial on this, but information technology'south possible with the right tools. Cleaning this component is a bang-up fashion to extend the life of the V8. Dust will buildup over time in this area, and cleaning will help it perform as good every bit new.
Since you'll be removing screws, place a make clean towel underneath your work area, and grab a ziplock pocketbook for storage to avoid misplacing it.
Alarm: Disassembling the cyclone is something I don't think Dyson recommends. Doing so may void the warranty. I would only recommend doing this if the unit you have is past the warranty coverage, and you're the blazon who likes to DIY.
Steps to disassembling Dyson V8 cyclone
1. Remove the pre-motor filter
Please accept out the pre-motor filter so it doesn't go far the way.
two. Empty dustbin
Pull the red lever to empty the contents (if any), so push a red lever (cheque photo) to release the dust container's outer shell.
Gear up it aside and make clean information technology afterward if dirty.
3. Remove the cyclone assembly
With the dustbin'south outer trounce off, locate the red lever you see on the photograph below.
Button the lever, then slide the whole assembly upwards.
Use a torque screwdriver to remove these four Torx screws.
Once the bolts are out, take out this component with the bolts and place it inside a ziplock pocketbook.
4. Utilise a flat tool to unfasten the screen filter
Grab a flat tool (like a flathead screwdriver) and gently pull it towards yous as you rotate the filter assembly.
I didn't use a flathead just instead this plastic tool.
Every bit you pull, yous will experience the clips loosen. Don't rush this step or gamble damaging the clips.
Once y'all've loosened the clips, pull the mesh filter out. Wipe a clean microfiber towel.
You could launder this with running water, only make sure to rinse it well and dry thoroughly to forbid corrosion.
5. Remove cyclones
Afterward taking out the mesh filter, you'll take access to the Torx screws holding the outer cyclone crush.
4 bolts are belongings it in place. Subsequently removing them, pull the cover. You could see how dirty this function is, and it's why I mentioned wearing rubber gloves.
In one case you've pulled out the outer cover, remove the inner part.
This time I used a microfiber towel considering it's filthy. No screws are holding information technology, and so pull it out.
Look at all the filth covering it.
6. Disassemble the meridian cyclone assembly
There are two Torx screws outside and another four inside the cyclones.
Here's the location of the two outer Torx screws (check photo).
And the inner screws. You may need a flashlight to discover the bolts' exact location because of all the dust roofing information technology.
Four screws are property the cyclones in place. Loosen all, and so dismantle.
The cyclonic system of the V8 has diverse layers.
There are as well 2 gaskets y'all need to clean—the pink/red outer gasket.
And another smaller gasket located underneath.
Store all the screws in a ziplock pocketbook to avoid losing it.
Lastly, remove this component from the whirlwind.
Carefully remove the inner and outer gaskets. Don't pull as well hard, or it will tear.
seven. Wash cyclone components
Clean the parts under running water. Some may recommend using liquid dish lather. I prefer using only h2o. If you determine to add dish soap, avert stiff detergents as information technology can degrade the plastic components. Also, apply a little and rinse well.
Employ a soft castor when washing the seals. These are delicate parts. Avoid scrubbing likewise hard.
Make sure at that place'due south no soapy residue left on all the parts earlier putting it back together.
Reassembling the V8 cyclone
It'due south 1 thing to dismantle, simply putting back the cyclones volition exist harder, and can be confusing.
So I created a separate department for this as a guide. Please note that I don't know the exact name of each element, then utilize the photos as a guide.
1. Attach the black gasket to this component.
Notice that the indentations are facing outward.
ii. Join the cyclone encompass and the role above.
three. Reattach the blood-red gasket
Again, brand sure the indentations of the gasket are facing outward.
four. Attach inner cyclone
The inner cyclone has five ports. I missed this part during my first attempt. So I had to detach to reattach this part.
v. Install the outer cyclone and fasten bolts.
Side by side, reattach the outer cyclone. There are six bolts holding it.
2 are located on the outer role (check photo below).
In that location are too iv bolts you have to tighten within the cyclones. A magnetic screwdriver will help to reattach the bolts.
6. Reattach the inner cyclone cover
This component doesn't have any screws.
7. So the outer cyclone cover
Don't forget to tighten the four bolts to secure it in place.
viii. Reattach outer mesh filer.
But clips hold the mesh filter. Place it on a flat surface and so push down until you hear the clips clamp on the frame. Double-check to run across the mesh filter is deeply fastened.
9. Connect the red lever on the whirlwind associates.
Tighten the four Torx screws.
x. Slide the cyclone assembly on the motor.
Line up the notches and slide the cyclonic component on the motor until you hear a clicking sound.
11. Reattach dustbin
The last step is to reattach the dustbin and pre-motor filter.
This video will help you with the step by footstep procedure of disassembling and putting back the cyclones.
Source: https://www.bestcordlessvacuumguide.com/how-to-clean-dyson-v8/#:~:text=However%2C%20one%20online%20vacuum%20store%20recommends%20cleaning%20it%20every%20three%20months.
Posted by: szaboswely1945.blogspot.com
0 Response to "How Frequently Should You Wash Your Dyson V8 Animal Filter"
Post a Comment